您要查找的是不是：
- The thinning drawing force is calculated through deforming work method and slip-line method irrespectively, and the results are compared in this paper. 本文用變形功法和滑移線法分別求解變薄拉深力,并將兩種方法的計算結果進行了比較。
- By analyzing the drawing stress of flux-cored wire(FCW),a new model for the calculation of the drawing force for FCW was formed. 通過藥芯焊絲拉拔應力分析,建立了冷軋鋼帶法制造藥芯焊絲的拉拔力計算模型,分析了影響拉拔力的因素。
- The strain and the stress site in course are achieved,and the influence of deformation and coefficient of friction on drawing force is analysed. 得到了拉拔過程中工件變形的應力、應變場等,并分析了變形程度和摩擦系數對拉拔力的影響。
- All die drawing numbers plus special die drawings will be supplied at preliminary review. 在初級設計中所有模具圖紙必須完全提供。
- This study affords a basis for further research of the relationship between strain and stress .and for solution of the drawing force as well as the maximum drawing force. 為進一步研究拉延工序變形過程中的真實應力應變關系、求解拉延力和最大拉延力奠定了基礎。
- Belt type drawing has applied imported deceleration motor and inverter, it has such advantages as reasonable structure, large drawing force, stable drawing, etc. 履帶式牽引機采用進口減速電機及變頻器，具有結構合理，牽引力大，牽引穩定等優點。
- Based on the assumption, the computer was used to calculate the minimum deformation energy, and the speed distribution in the deformed area and the drawing force were gotten. 在此基礎上利用流函數建立了變形區速度場，并利用計算機對變形能進行求極小值，得到了變形區的速度分布及拉拔力。
- Under the collective drive of draw force, push force and catalyze force, the organization mode of value chain integration evolve to virtual re-integration mode. 在拉動力、推動力和催化力的共同驅動下，價值鏈整合的組織模式向模塊化虛擬再整合的組織體系演進。
- A great posterior ground reaction force is associated with a great quadriceps muscle force, which would cause a great anterior draw force at the proximal end of the tibia. 其中較大的地面反作用力引發較大的股四頭肌力和脛骨近端向前的拉力從而增加前交叉韌帶負荷。
- The paper makes a quantitative analysis and calculation for belt's creeping quantity and creeping velocity. which will bring advantages to improve the drawing force or braking force of drum surface. 本文對帶式輸送機膠帶的蠕動量和蠕動速度進行了定量分析和計算，有利于提高滾筒表面的牽引力或制動力。
- CALCULATION OF FORCE AND ENERGY PARAMETER IN PROCESS OF ROLLER DIE DRAWING 輥模拔絲力能參數的計算
- This experiment researched the drawn force of the single centrum pedicle screws. 此次實驗研究的是單個椎體的螺釘拔出力。
- Compared to conventional wire drawing, the drawing forces can be reduced greatly by applying ultrasonically oscillating. 超聲振動還可以減小金屬絲的不均勻變形，有利于表面質量的提高。
- Every winter some old people die from hypothermia. 每年冬天都有些老人死于體溫過低。
- ADVANCES IN BIAXIAL ORIENTED POLYMER TUBES BY DIE DRAWING 口模拉伸成型法生產雙軸取向管的研究進展
- Little does he care whether we live or die. 他一點也不管我們是死是活。
- vibrating wire [resonant wire] drawing force meter 振弦式拉力計
- Nowadays many people die of cancer. 現在有很多人死于癌癥。
- She's ambitious and eager to get on(in die world). 她雄心勃勃，迫切地想成功。
- Study on drawing force of flux-cored wire 藥芯焊絲的拉拔力計算模型
