您要查找的是不是：
- impression die forging with small flash 小飛邊模鍛
- Squeeze casting is descrbed as having a combination of the virtues of gravity die casting and closed die forging. 擠壓鑄造被認為兼具有壓力鑄造和合模儔造的優點。
- The main application range of die forging process on screw press are summarized. 本文總結了螺旋壓力機模鍛工藝技術的主要適用范圍。
- Above result revealed that multidirectional closed die forging of spiral bevel gear was feasible. 揭示了使用復動閉式模鍛模具成形小錐角螺旋傘齒輪的可行性。
- Abstract： Using the feature technique,a set of flashless die forging CAPP system for gear blanks is developed. 摘 要： 運用特征技術，開發了一套齒輪坯的閉式模鍛CAPP系統。
- The results have shown that the new way of precision die forging is very efficient. 結果表明，閉式精密模鍛工藝的新方法是十分有效的。
- Using the feature technique,a set of flashless die forging CAPP system for gear blanks is developed. 運用特征技術,開發了一套齒輪坯的閉式模鍛CAPP系統。
- It has elaborated the advantages replacing open -die forging with flashless die forging technology. 闡述了用閉式模鍛工藝代替開式模鍛的優點。
- Based on the closed die forging process and the FEM simulation for the pole, the mould structure for precision alternator pole forging is designed. 在磁極的精密模鍛生產工藝分析和有限元模擬基礎上,設計了磁極精密模鍛新工藝參數和新型的鍛模結構。
- As the Close die forging hammer is working in atrocious condition, its maximum intense part-anvil block must bear frequent shock and overload. 摘要模鍛錘由于其特別惡劣的工作條件，其上最大的受力零件-砧座，會(huì )受到頻繁的沖擊和過載。
- This paper analyzed the technology of all kinds of spiders, and put forward the corresponding method of die forging technology. 對各種規格的十字軸進行工藝分析，并制定相應的模鍛工藝方法。
- Abstract: The characteristic of driving system for the dispenser used in ten-thousand-ton multidirectional die forging hydraulic press was analyzed. 摘 要： 分析1萬t多向模鍛水壓機分配器驅動系統的結構特點，提出一種智能超差二次調整控制算法。
- Such systems can greatly increase the technical designing effeciency and quality of flashless die forging in gear blanks. 該系統能極大地提高齒輪坯的閉式模鍛工藝設計的效率和質量。
- Tests and researches are conducted for microstructure,residual stress,dislocation density and hardening principle of starlike inner race formed by cold closed die forging method. 針對經閉塞冷鍛成型的星形套的組織、殘余應力、位錯密度及硬化規律進行了試驗研究。
- The conception and key characteristics of virtual prototyping technology and the advantage of using it to design the driver of 300 MN die forging hydrostatic press were discussed. 在分析傳統機械設計方法中所存在的問題的基礎上,論述了虛擬樣機技術的概念、主要特點及其用于300MN模鍛水壓機接力器設計的優點。
- The method of applying local loading to die forging was introduced in this paper. And a program for calculating the die filling efficiency was developed. 本文介紹了在模鍛工藝中實現局部加載的方法，編制了計算局部加載時模腔充填效率的電算程序。
- Analysis on forging technolgy of transverse arm part has been introduced, upon which technics flow of die forging has been designed, with design of forging die cavity. 通過對轎車左右橫臂的結構及鍛造工藝分析,制定了其模鍛工藝流程,介紹了模鍛工藝及其工步型腔設計。
- The central problem, appearing in the process of flashless die forging of cylindrical gear blanks, may be the fold in inner bore and the local unfilled zone. 圓柱齒輪坯的閉式模鍛工藝中,可能出現的主要問題是內孔折紋和局部不充滿。
- My general impression was that it was quite good. 大致上我覺得那相當好。
- Her gentleness has given me a deep impression. 她的親切給我留下了很深的印象。
