您要查找的是不是：
- A systematic deviation of a value from a reference value. 某數值偏離參考值的一種系統偏差。
- Are her views to the left or right of centre? 她的觀點是中間偏左還是偏右?
- The lateral deviation of a projectile or bomb. 炸彈或射彈的側位偏差
- Be her view to the leave or right of centre. 她的觀點是中間偏左還是偏右。
- Variated Rhetoric is the deviation of rhetoric. 變異修辭亦稱常規修辭的偏離形式。
- Their political views are right of centre. 他們的政治見解總是中間偏右。
- SD: Standard deviation of the fit. 擬合的標準偏差。
- Deviation of a single width of the inner ring. 內圈單一寬度偏差。
- Deviation of a single width of the outer ring. 外圈單一寬度偏差。
- Deviation of synchronous time from standard time. 同步時間與標準時間的偏差。
- Limited distance deviation of the optional bolt hole on flange shall be 2mm. 法蘭上非強制螺栓孔的有限距離偏差應該為2毫米。
- Center height deviation of rodends or ball joint rod ends. 桿端關節軸承或球頭桿端關節軸承中心高偏差。
- The signs consist of: model, type(centre distance), nominal transmission ratio, the kind of added electric motor and the way of input or output. 減速機的型號由型式代號、機座規格（中心距）、公稱傳動比、所配電機類型及大小和輸入、輸出方式要求代號組成。
- Actual deviation of height of the spherical plain thrust bearing. 推力關節軸承實際高度偏差。
- Conclusion:The standard deviation of the linearities is very small. 結論:酶促反應曲線開始階段有較好線性,可作為評價指標;
- The kinematic characteristics of chain drives are analyzed, the relationships between the speed and acceleration of the driven sprocket and the centre distance are given. 本文對鏈傳動運動學特性進行了分析，給出了從動鏈輪速度、加速度與中心距之間的關系。
- The equation of the centre distance change when the corrugating machine moves accurately was deducted, which describes the displacement, speed, and acceleration. 同時也對紙板成型質量產生皺褶，楞高不一致，甚至產生裂紋。
- The further the deviation of the tone from the musical note, the further is the red bar from the centre. 曲調離正確音律越遠，則紅條也離中間越遠。
- The minimum centre distance is sometimes governed by the amount of chain lap on the driver sprocket, our normal recommendation in this circumstance being not less than six teeth in engagement with the chain. 最小中心距有時由驅動鏈輪輪齒與鏈條接觸數量決定，在這種情況下我們通常建議有不少于6個的輪齒與鏈條嚙合。
- Such as the mean radius of asperity peaks,the mean asperity distance,the density of asperities and the standard deviation of asperity height. 為了實現微觀表面粗糙峰特征參數的獲取,提出了一種結合小波分析和分水嶺分割法的微觀表面形貌分析方法。
