您要查找的是不是：
- Niobium is the metallic element with the highest transition temperature. 鈮是轉變溫度最高的金屬元素。
- At the same time, visionary delivery design transit from the old-fashioned styel which is largely a surfical and static way, to one that values active and multiple expressions. 與此同時，也使視覺傳達設計由以往形態上的平面化、靜態化開始逐漸向動態化、綜合化方向轉變。
- In addition, many suspected that 23 K was close to the maximum transition temperature possible for a traditional superconductor. 此外很多人也認為，23K已經接近傳統超導體最高轉變溫度的極限。
- The point groups above and below the transition temperature are Amm and m respectively. 相變溫度上下晶體點群分別為4mm和m。
- We defined the transition of FCGR as a fatigue ductile-brittle transition temperature (FDBTT). 本文將疲勞裂紋擴展速率發生轉折的溫度定義為疲勞裂紋擴展的韌脆轉化溫度FDBTT。
- The crystalline pattern of Chestnut starch was C and the glass transition temperature was 147.7C. 板栗淀粉的晶型屬于C型，板栗淀粉的玻璃化轉變溫度為147.;7℃。
- DSC, which verified the transition temperature of LC phase,detected two of them, other related tests are in progress. 其中兩個化合物做了差熱分析(DSC)測試,證實有液晶相變化出現,其它相關測試在進行中。
- The glass transition temperature(Tg) of HBPS-1, HBPS-2 and HBPS-3 were studied by DSC. 示差掃描量熱法(DSC)的分析結果表明：HBPS-1、HBPS-2、HBPS-3的玻璃化轉變溫度按順序降低，且均低于線形聚苯乙烯的玻璃化轉變溫度；
- The results show the existence of a characteristic transition temperature of coking process in TLE. 反之,表面縮聚反應過程為控制步驟。
- The glass transition temperature of the WPC does not change after about 1000 hours under high temperature. 木塑材料在經歷了近1000小時的高溫老化后，其玻璃化溫度幾乎不變。
- The FE-AFE temperature decreases and the AFE-PE transition temperature increase with hydrostatic pressure increasing. 隨著壓力增大，鐵電-反鐵電相變溫度降低，反鐵電-順電相變溫度升高。
- All polyesters have low phase transition temperature, they have good solubilities in common organic solvents. 所有聚酯均具有較低的相轉變溫度,在普通的有機溶劑中具有較好的溶解性質。
- The liquid crystal phase states and phase transition temperature and hysteresis loops proved their ferroelectricity. 經元素分析和紅外光譜分析確證了其結構，并進行了相態、相變溫度和電滯回線的測定，證實其為鐵電液晶。
- The influence of emulsion particle size and glass transition temperature, etc on film performances is discussed. 討論了丙烯酸酯乳液的粒徑大小、玻璃化轉變溫度等對涂膜性能的影響。
- The glass transition temperature and the thermal decomposition of PDLLA were determined by DSC and TGA. 用DSC,TGA分析了不同分子量PDLLA的玻璃化轉變和熱失重。
- And the DSC thermograms demonstrate the same tren d of theglass transition temperature of the modified resins. 測定了改性產物的DSC曲線，發現隨著反應物中對氨基苯甲酸比例的提高，改性產物的玻璃化轉變溫度升高。
- During the air pressure test, the test temperature shall be higher than the brittle transition temperature of the metal material. 氣體壓力的試驗時,試驗溫度必須高于金屬材料的脆性轉變溫度。
- The experimental results show that water jet impingement induces higher heat flux, higher critical temperature and narrower transition temperature range. 水冷實驗數據分析結果表明：射流能提高熱流密度和臨界溫度，縮小過渡區溫度區間。
- The addition of a plasticizer may lower the melt viscosity, elastic modulus, and glass transition temperature (Tg) of a plastic. 同時,加入增塑劑,還可以降低塑料在熔融態時的粘度、彈性模數及玻璃轉變溫度(tg)。
- Even an oversight in the design might issue in heavy losses. 設計中那怕是一點點疏忽也可能造成重大的損失。
