您要查找的是不是：
- WUXI XUSHI NUMERICAL CONTROL PART CO., LTD. 無錫徐氏數控機床部件有限公司。
- Correct control algorithm is the key of network congestion control. 因此,正確的控制算法是網絡(luò )擁塞控制的關鍵。
- A control part controls the storing part and the display part. 一控制部分控制該存儲部分和該顯示部分。
- When referencing or casting controls, be sure to use the correct control type. 引用或強制轉換控件時,一定要使用正確的控件類型。
- This system has no special requirement for original equipment and control part with simple installation. 該系統自成體系,對原有設備及其控制部分沒有特殊要求,且安裝簡單。
- Breath is a drive in singing and phonation, and good singing can t be achieved without correct control of breath. 氣息是歌唱發聲的動力,沒有正確的氣息控制就沒有好的唱歌。
- This escaper uses for clockwork spring,as transmission control part of auto record instrument for enery. 本擒縱器用于以發條為能源的各類自動記錄儀表作為等時傳遞控制元件。
- And make sure that you put the correct controls on the form. 確保對窗體設置了正確的控件。
- Drive and control part: adopting AC frequency conversion speed, drive step by step, digital closed loop control system. 五、傳動及控制部：采用交流變頻調速，分步傳動，全數字閉環控制系統。
- The correct control of inking amount is the most important factor for print quality. 摘要輸出墨量的正確控制是影響印刷質量的最重要因素之一。
- Now, access control part of the MIS-for-SD has been being used by the third logistic service management centre, CUIT. 目前，系統的管理權限的功能部分可交付給成都信息工程學院（本部）第三后勤服務管理中心使用。
- It is essential to study the causes of riverbed entrenchment,so as to find out correct control measures. 要克服這些問題的發生,必須研究河床下切的原因,才能提出有針對性的解決措施。
- The magnetic circuit control part includes plastic structure in outer layer and electrified winding enwound on stator. 磁路控制部分為外層塑料結構及在定子上纏繞的通電線圈。
- This paper introduces the reformation experiences of the ration package scale's logic control part. 本文主要介紹定量包裝秤邏輯控制部分的改造經驗及實施效果。
- Control chart: Principle of control chart, how to choose correct control chart, introduction of most often used control charts. 控制圖原理,如何選擇適當的控制圖,幾種常見的控制圖的使用。
- PID control based on iterative control compensation is used in position control part. 在位置控制部分,采用了基于重復控制補償的PID控制方法。
- This paper also analysis the key links of dehydrating station's production.The correct control method for the industly sites are obtained. 并對脫水站的重要生產環節進行研究分析，從而得出符合工業現場實際的控制辦法。
- The control part adopts the PLC and imported wiring, The circuitry is simple and running credibility, degree of automation is high. 控制部分采PLC和進口電器,線路簡單,運行可靠,自動化程度高。
- The chip pin are connected with the control panel of the electric control part to make the system can be reassemble and expandable. 并遵循開放性的原則,設計將實驗電路板上的相應引腳,引出至電氣控制柜的控制面板,以實現實驗系統的可重組性和可擴展性。
- The main work of the base-band process part of the receiver is demodulation and decoding, the link control part does the framing and forwarding. 接收機的基帶處理部分主要是解調和譯碼，鏈路控制部分組幀和轉發。
