您要查找的是不是：
- copper clad plate 敷銅板
- SHANGHAI NANYA COPPER CLAD LAMINATE CO., LTD. 上海南亞覆銅箔板有限公司。
- Nanmei Copper Clad Laminate Factory Ltd. 南美覆銅板廠有限公司。
- A preliminar application of the polyimide film to two layer flexible copper clad lamination was studied. 對該聚酰亞胺在二層柔性覆銅板上的應用進行了初步研究。
- Keywords： printed circuit board, plated through hole, copper clad laminate, epoxy. 關鍵詞：印刷電路板，貫孔，銅箔基板，環氧樹脂
- The ARB technique not only increased greatly the bonding strength of TA1/Q235 clad plate,but also thinned the microstructure of Q235 plate. 結果表明采用累積疊軋焊方法不僅可以大幅度地提高TA1/Q235的結合強度,而且還可以獲得連續均勻、組織細化的Q235的結合組織。
- The copper clad laminate automation system is designed and realized by using Program Logic Controler(PLC). 摘要簡要闡述了用可編程控制器(PLC)實現對銅箔覆膠機自動控制的方法。
- Clad plate,which is made of titanium/steel, is tore in the edge of the plate during the process of explosives welding. 鈦/鋼復合板在爆炸焊接工藝中四周邊角被撕裂現象嚴重,是爆炸焊接鈦/鋼復合板的難點之一。
- Welding material selction of clad plate refers to those of the same clad material respectively. 復層焊接材料挑選參考異類復層材料焊接時選用的焊接材料。
- I'm looking for a small quantity (only 2 at the moment) of insulated copper clad aluminum wire for an electromagnet project. 我在為一個電磁項目尋找小量（目前只有2根）絕緣銅鋁電線。
- After burying copper clad steel grounding pole underground, nomatter natural corrosion or electrochemistry reaction, it has strong protection ability. 銅包鋼接地極深埋地下后，無論是自然腐蝕還是電化學反應，都有極強的保護性。
- When explosive welding the big and thick stainless steel clad plate, there are some quality defects of small area melding in interface appeared random. 摘要爆炸焊接中厚不銹鋼復合板時，板面容易隨機產生小面積的界面熔化缺陷。
- We have 150 skilled staff,own kinds of advanced special Lacquered Aluminum Wire and Copper Clad Aluminum product equipments,detection devices. 公司員工150人，擁有各種先進的銅包鋁、鋁漆包線生產專用設備、檢測設備叁拾余臺（套）。
- The practice proved that the welding quality of stainless steel clad plate was very steady if following the welding points. 實踐證明,只要遵循其焊接要點,不銹鋼復合鋼板的焊接質量是非常穩定的。
- This paper initially discussed synthesis and modification of tetrafunctional epoxy resin(1,1,2,2- tetrakis(hydroxy phenye)ethane),as well as application in copper clad laminate. 對四官能環氧樹脂[1,1,2,2-四(對羥基苯基)乙烷四縮水甘油醚]的合成與改性及在覆銅板中的應用作了初步探討,并對其屏蔽紫外線與產生熒光的機理作用作了簡單闡述。
- Various polyimide was synthesized from 3-BAPP with various dianhydrides.The application of the polyimiders to two-layer flexible copper clad laminate (2L-FCCL) was researched. 用3-BAPP與多種二酐合成出多種聚酰亞胺，并在二層法撓性覆銅板(2L-FCCL)的應用方面做了一些研究。
- The characteristic of thermosetting polyphenylene oxide resin copper clad laminates as wel as their application in the high frequency printed circuit board is introduced. 論述了熱固性聚苯醚樹脂基覆銅板的特性及其在高頻印刷電路板上的應用。
- Cyanate compound, the preparation of triazine copper clad panel and 1ts application in high frequency printed circuit board were introduced in this paper. 本文介紹了氰酸酯化合物，三嗪覆銅板的制備及其在高頻線路板上的應用。
- Therefore, polyimide has been widely used in Flexible Copper Clad Laminate (FCCL) and semiconductorcomponents of the internal package as the insulating material. 目前產業界對于聚醯亞胺的需求日盆提升，相對的對于聚醯亞胺的要求條件也越來越嚴苛。
- The paper analyzed the welding characteristic of stainless steel clad plate, and summarized three factors that were welding groove, welding materials and parameter, welding sequence. 對不銹鋼復合鋼板的焊接特點進行了理論分析,總結出其焊接三要素:焊接坡口、焊接材料和參數、焊接順序。
