您要查找的是不是：
- WUXI XUSHI NUMERICAL CONTROL PART CO., LTD. 無錫徐氏數控機床部件有限公司。
- A control part controls the storing part and the display part. 一控制部分控制該存儲部分和該顯示部分。
- This system has no special requirement for original equipment and control part with simple installation. 該系統自成體系,對原有設備及其控制部分沒有特殊要求,且安裝簡單。
- This escaper uses for clockwork spring,as transmission control part of auto record instrument for enery. 本擒縱器用于以發條為能源的各類自動記錄儀表作為等時傳遞控制元件。
- Drive and control part: adopting AC frequency conversion speed, drive step by step, digital closed loop control system. 五、傳動及控制部：采用交流變頻調速，分步傳動，全數字閉環控制系統。
- Now, access control part of the MIS-for-SD has been being used by the third logistic service management centre, CUIT. 目前，系統的管理權限的功能部分可交付給成都信息工程學院（本部）第三后勤服務管理中心使用。
- The magnetic circuit control part includes plastic structure in outer layer and electrified winding enwound on stator. 磁路控制部分為外層塑料結構及在定子上纏繞的通電線圈。
- This paper introduces the reformation experiences of the ration package scale's logic control part. 本文主要介紹定量包裝秤邏輯控制部分的改造經驗及實施效果。
- PID control based on iterative control compensation is used in position control part. 在位置控制部分,采用了基于重復控制補償的PID控制方法。
- The control part adopts the PLC and imported wiring, The circuitry is simple and running credibility, degree of automation is high. 控制部分采PLC和進口電器,線路簡單,運行可靠,自動化程度高。
- The chip pin are connected with the control panel of the electric control part to make the system can be reassemble and expandable. 并遵循開放性的原則,設計將實驗電路板上的相應引腳,引出至電氣控制柜的控制面板,以實現實驗系統的可重組性和可擴展性。
- The main work of the base-band process part of the receiver is demodulation and decoding, the link control part does the framing and forwarding. 接收機的基帶處理部分主要是解調和譯碼，鏈路控制部分組幀和轉發。
- The system is made of hydraulic press,rectangular box drawing die of divided blank holder,hydraulic part of blank holder and control part. 該系統主要由液壓機、壓邊圈分區的矩形件拉深模具、壓邊裝置的液壓部分以及控制部分組成。
- Introd uce detailed the several important part, especially the motor control part and t he produce theory of the PWM signal. 給出了一個控制算法，經過實驗說明了該設計的可靠性。
- The control parts of the digital ultrasonic welding machine are introduced. 介紹了一種數控的超聲波焊接機的控制方法。
- This Recommendation contains a detailed set of tests for the Signalling System No. 7 Signalling Connection Control Part(SCCP). 本建議包含了一組詳細的對七號信令系統信令接續控制部分(SCCP)的測試。
- Resistance (value) between the end terminal and the sliding terminal when the control shaft (control part) is in its full CW or CCW position. 動觸點調到相應終端止檔時，引出端與動觸點引出端之間得到的阻值。
- The unlocking control part receives an unlocking instruction signal to make the actuator perform the unl ocking operation. 解鎖控制部接收解鎖指令信號，使 致動器進行解鎖動作。
- This machine consists of winding part ,separating part,drive storage part ,extruding part,electric heating part ,electric control part,tec. 用于摩托車胎，輕卡車胎，載重輪胎，工程輪胎等的方斷面鋼絲圈的纏繞。
- The primary function of the Signaling Connection Control Part (SCCP),the transport layer) is to support the transfer of TCAP,OMAP and MAP data between network nodes. 信令連接控制部分 (SCCP)，傳輸層，最主要的一個功能就是支持 TCAP、OMAP 和 MAP 數據在網絡(luò )節點間的傳輸。
