您要查找的是不是：
- DISCONNECT THE SEAT BELT CONTROL MODULE. 拆卸座位安全帶控制模組。
- KEY OFDISCONNECT TRANSMISSION CONTROL MODULE. 關閉。拆開變速控制模組。
- Designed the air conditioner control modul based on sensors to check the air conditioner , so that energy was saved. 并且，以家用空調器為對象，設計了以傳感器為核心的監測模塊，通過檢測環境溫度來調整空調的工作狀態，達到了節約能源的目的。
- Check control box it is connected completeness and exactness. 2檢查電器控制箱電源接線的完整性和正確性。
- DISCONNECT THE BODY 20-WAY CONNECTOR (AT BODY CONTROL MODULE). 拆除車身20－路接頭（位于車身控制部件）。
- GAIN ACCESS TO THE BODY CONTROL MODULE BUT DO NOT DISCONNECT. 找出車體控制模組，但不要斷開。
- The OLE control module failed to register correctly. OLE控件模塊未能正確注冊。
- DISCONNECT & REMOVE THE BODY CONTROL MODULE FROM THE JUNCTION BLOCK. 從集成板上拆下并移走主體控制模組。
- An electronic control module is provided for each pair of actuators. 一個中央控制和電源系統可對兩個傳動裝置進行調節。
- Damage Control module descriptions now list the correct hull resistance. 傷害控制模塊描述修正,列出正確的船殼抗性,技能與插件。
- Third, multi-duty direction pattern microminiaturized attitude control module. 三是多任務指向模式的微型化姿控模塊。
- Sends a signal from the oil pressure sending unit to the Powertrain Control Module (PCM) relating to engine oil pressure. 從燃料壓力發送單元發送一個信號給動力傳達系控制模組(PCM)，此信號與引擎燃油壓有關。
- In computer network communication, adopted the error- check control methods to reduce the error code frequency of data transmission commonly. The CRC (Cyclic Redundancy Check) method is the best one of them. 循環冗余碼校驗CRC是計算機網絡(luò )通信中最常采用的數據校驗方法之一,CRC方法能夠很好地降低數據傳輸的誤碼率。
- This paper introduce the application of koyo PLC, especially it's servo control module in bearing grinding machine. 本文介紹了plc，特別是其伺服定位模塊在軸承磨削加工中的應用。
- Do not disconnect the connectors or remove the body control module from the junction block. 不要從功能塊斷開接頭或移走控制體
- The control strategy consists of optimal shift decision-making module and gear shifting process control module. 該策略將換擋控制過程分為最優擋位決策模塊和換擋過程控制模塊兩部分。
- The plumber made a careful check of the pipes. 管子工對管道做了仔細的檢查。
- The Design Based on the Monolithic Integrated Circuit Chamber Temperature Control Module. 基于單片機控制的爐膛溫度測控模塊設計。
- The application of thermostatic control module based on PID in opacimeter was introduced. 介紹了基于PID算法的恒溫控制模塊在不透光煙度計中的應用。
- The adpter is composed of a bus interface module,a logic control module,an encoder/decoder and a transceiver module. 紅外無線串行通信適配卡有四個模塊：總線接口模塊，邏輯控制模塊，調制解調模塊，發射接收模塊。
