您要查找的是不是：
- A mathematical model for predicting short die extrusion swell is presented which is preliminarily tested by using the experimental measured data of rubber compound in capillary extrusion. 提出一預測短口型擠出脹大的數學模型，并引用混煉膠毛細管實驗測量數據進行初步驗證。
- Merz-Colwell extrusion rheometer 梅爾茨-科威爾擠壓式流變儀
- Keywords ceramic paste;extrusion;extrusion rheometer;extrusion parameters; 陶瓷坯料;擠壓成型;擠出流變計;流變參數;
- Progress in Study of Linear Polymer Melt Fracture in Capillary Extrusion 線型聚合物毛細管擠出中熔體破裂研究進展
- The end pressure loss of LLDPE melt in short die extrusion and factors affecting the pressure loss were investigated by using a capillary rheometer. 應用毛細管流變儀,考察了線性低密度聚乙烯(LLDPE)熔體于短口型擠出流動中的末端壓力損失及其影響因素。
- The flow behaviour of two polystyrene melts, styron 498 and styron 492J, in extrusion were investigated by using a capillary rheometer. 應用毛細管流變儀,考察了兩種聚苯乙烯-Styron498(PS498)和Styron492J(PS492J)熔體擠出過程中的流動行為及其影響因素。
- The rheological properties of PLA chip were measured by extrusion capillary rheometer at different temperatures and shear rates. 摘要以聚乳酸切片為原料，在不同溫度下，利用毛細管流變儀測試其流變性能。
- Abstract:The flow behaviour of PP/EPDM/glass bead (GB) composite during extrusion at 463 K was investigated with a constant rate capillary rheometer. 摘要：采用恒速率型毛細管流變儀，考察463 K下PP/EPDM/玻璃微珠復合材料的擠出流動性。
- Dynamic extrusion experiments for polymer melts were done on the invariable speed type capillary dynamic rheometer (ISTCDR) made by the author. 在自行設計的恒速型毛細管動態流變裝置上,對聚合物熔體進行動態擠出實驗。
- The high speed extrusion behaviors of several polyolefine melts were investigated by a double capillary rheometer of constant speed type. 闡述了抗靜電劑的種類、作用機理和選用原則,以及抗靜電劑在聚烯烴中的應用和國內最近的研究進展。
- The rheological properties of low density polyethylene (LDPE) were measured under conditions close to the practical extrusion process by means of a capillary rheometer. 應用毛細管流變儀測量了在接近實際擠出工藝條件下低密度聚乙烯熔體的流變性質;
- extrusion rheometer 擠出式流變儀
- press-flow extrusion rheometer 壓流型擠出流變儀
- Test Method for Measuring the Rheological Properties of Thermoplastics with a Capillary Rheometer (08. 用毛細管流變器測定熱塑料的流變性能的試驗方法(08。
- The rheological behavior of PET synthesized with MTA was studied with Rosand capillary rheometer. 采用英國Rosand公司RH7-2X型毛細管流變儀對自制的MTA合成PET樣品的流變性能進行了研究。
- The rheological property of polytrimethylene terephthalate( PTT) was studied with capillary rheometer. 采用自制的毛細管流變儀研究了聚對苯二甲酸丙二醇酯(PTT)的流變性能。
- Rheological characteristics of HDPE／NBR blends prepared by mel ting blending was studied with capillary rheometer. 通過熔融共混法制備了HDPE／NBR共混物，用毛細管流變儀研究了其流變特性。
- The die-swell behaviour of tube compound under the experimental conditions was investigated by capillary rheometer. 用毛細管流變儀考察了內胎膠擠出口型膨脹行為。
- capillary extrusion 毛細管擠出
- The springboard is made of an aluminium extrusion. 跳板是鋁制的擠壓板。
