您要查找的是不是：
- J. Vertical Shaft Fine Adjustment Screw. 垂直桿微調螺絲.
- Tighten adjustment screw to 3 N·m (30 in-lbs) torque. 擰緊調整螺絲到3 N·m (30 in-lbs)扭力。
- Loosen the adjustment screw, and adjust the length of the link rod. 請擰松調整螺絲，拔出或插入連接桿進行調整。
- Firmly screw can on adapter, and turn the flow adjustment screw. 將料罐倒置與噴槍連接，旋轉打開流量閥，調節流量。
- Remove adjuster lever, adjuster screw and spring. 拆卸調整器桿，調整器螺絲和彈簧。
- The high step moves from under the adjusting screw. 使高點從調節螺釘下移動。
- Presser foot adjustment screw graved with graduation makes digital pressure control easy and precise. 壓腳調節螺栓上刻有刻度，數字化調節更易控制壓腳壓力，因此，壓腳壓力可輕松而準確的重設。
- The adjusting screw rests on the high step of the cam. 調節螺釘落在凸輪高點上。
- Keeping well away from the propeller, adjust the engine to maximum rpm with the mixture adjustment screw marked with an "H". 跟螺旋槳保持距離;推油門全開.;轉進標記"H"螺絲求取最高轉速。
- Adjustment of parallelity, adjust screw (6), you can set the parallelity between printing squeegee and ink-collecting squeegee. 平行度調整:調節螺絲(6),可調整刮墨刀、回油刀與絲網的平行度。
- To Readjust- Loosen lock nut on the adjusting screw. 重新調節：松開調節螺絲上的鎖定螺母。
- Brake assembly, Brake adjusting arm, Under Carriage parts, Gearbox for Automobile, casting of SG Iron and Grey Iron. 重卡車剎車轂總成,剎車調整臂總成,輪邊減速器總成,底盤懸掛件。輕型車各種變速器殼體。各種球墨鑄鐵、灰鑄鐵汽車鑄件。
- Lubricate adjuster screw threads and pivot with spray lube. 使用噴霧潤滑油潤滑調整器螺絲螺紋和樞軸。
- To Readjust - Loosen lock nut on the adjusting screw. 重新調節：松開調節螺絲上的鎖定螺母。
- Tie-Rod of Marble Gang Saw with hydraulic driven is for connecting hydraulic tensioner and saw blade. It composes of Rear Tie-Rod, adjust screw and wedge. 大理石框架鋸液壓鋸夾用于連接液壓漲緊器和鋸條，它由前后鋸夾，蝴蝶板、插板和調整螺桿組成。
- Remove compression from spring by turning adjusting screw (1) counterclockwise. 通過反時針?lè )较蛐D調節螺絲(1)從彈簧上拆卸壓縮件。
- Match of motor vehicle and S-shaped cam drum brake adjustment arm 汽車S型凸輪鼓式制動器間隙自動調整臂與整車的匹配研究
- Heavy duty adjusting screw. Adjusting screw is both slotted and knurled. 重型調節螺絲。調節螺絲既有槽也有花紋邊。
- Adjust adjustment screw 2 of the amount of bobbin thread to be wound round the bobbin so that the bobbin is wound with thread about 80%.Turn the adjustment screw 2 clockwise to increase the bobbin thread amount or counterclockwise to decrease it. 用繞線量調節螺絲2進行調節，讓線繞到80%25 。向右轉動繞線量調節螺絲2繞線量變多，向左轉動則變小。
- He pushed hard on the brake pedal to avoid a collision. 他使勁踩下煞車踏板以避免撞車。
