您要查找的是不是：
- The Nonlinear Finite Element Analysis on Crack of Negative Bending Moment Area in Steel-Concrete Composite Girder 鋼-混凝土組合梁負彎矩裂縫非線性有限元模擬分析
- The actual stress is not proportional to the bending moment. 實際上應力與彎矩不成正比。
- But the bending moment at the central hinge must vanish. 但在中間鉸處，彎矩必定為零。
- The induced bending moment may lead to destructibility of the pipeline. 彎矩的產生可能導致管線的破壞。
- Shear force is implicit in the development of bending moments. 桿中的剪力在彎矩的推導中是不明顯的。
- This increases both the rigid body rotation of the vehicle and the bending moment. 這既增加了飛行器的剛體轉動，也增加了彎矩。
- In the FEM simulation of the loading identification process, the bending moment maintains a constant amplitude, hut its direction is alterable. 在有限元仿真計算中，彎矩載荷的大小保持不變，但方向可調。
- Cracking of concrete flange slab in the negative moment area in steel-concrete composite continuous box beams affects its application for longer spans. 鋼箱-混凝土組合連續梁負彎矩區混凝土的開裂問題影響了這類組合結構向更大跨度的發展。
- The unique phenomena at any cross section of EULER compressive bar under the zero bending moment is analyzed. 從理論上分析了歐拉壓桿任意截面上彎矩為零的狀態下所出現的奇異現象。
- In addition, contrasted in the experimental foundation has analyzed presently about the composite beam hogging moment area crack width formula. 此外，在試驗的基礎上，對比分析了現行關于組合梁負彎矩區裂縫寬度的計算公式。
- In this paper a function calculation method of preloaded bending moment distribution for leaves of spring is des... 本文介紹了一種用于板簧簧片預加彎矩分配計算的函數計算法,并給出了計算實例。
- The needed pipe bending moment、wall thickness reduction and ovality of section are known by simulating. 通過模擬,計算管子彎曲變形所需的彎矩,計算管子彎曲部分外壁減薄率和橢圓度。
- Moreover, the influence of initial crookedness would be reduced as slenderness ratio and bending moment are increased. 初彎曲對桿件的影響隨長細比和彎矩的增大而減??；
- The bending moment of common prestressed concrete pipe piles is relatively low under the horizontal earthquake action. 摘要普通預應力混凝土管樁在水平地震作用下抗彎能力較差；
- The connection of CHS T-joints with fold chord subjected to in-plane bending moment can be simplified as rigid joint. 在平面內彎矩作用下，弦桿為折桿的T型圓鋼管節點計算可以簡化為剛接節點模型。
- The calculation of ledger maximum bending moment and deformation the even load of scaffold board and live loads above the ledger. 按照大橫桿上面的腳手板和活荷載作為均布荷載計算大橫桿的最大彎矩和變形。
- The Settlement both vertically and horizontally under lateral loads and bending moment must not exceed predetermined and acceptable values. 垂直和水平向荷載作用下的沉降和彎(曲)矩不能超過預先確定數值或工程采用的限定數值。
- The bending moment can be related to the formation drillability, BHA configuration and drill bit size, and is proportional to the applied WOB. 鉆頭彎矩與交錯層的可鉆性、下部鉆具的結構和鉆頭的幾何尺寸有關,并且與所加的鉆壓成正比。
- The results show that the acting planes of the bending moments which cause such a stress field that the maximum stress appears in the crack damage area of the case have an angle range of 0o to 20o against the longitudinal symmetric plane of the car. 研究結果表明，最大應力出現在離合器殼體裂紋萌發區域的彎矩載荷，其作用平面相對于汽車縱向垂直平面朝左傾斜約為0o至20o。
- The bending moment,axial force of the pile and subfloor are also analyzed.Then it draws some conclusions useful to practical engineering. 對開挖引起的地面、建筑物角點的沉降規律做了分析與探討,同時也分析了樁和底板的彎矩、軸力、剪力等變化規律,得出了有意義的結論。
