您要查找的是不是：
- Generator Belt Tension Adjust Bracket 發電機皮帶張力調整托架
- Check and repair radiator and thermostate; adjust the fan belt tension. 檢查并修理散熱器、調溫器，調整風扇皮帶張緊力。
- The 0.5 hp motor was mounted on vertical rails at the back of the headstock-end leg and could be moved up and down, to adjust the belt tension. 0.;5馬力電機安裝在垂直導軌背面的啟閉年底腿，可以向上和向下移動，以調整皮帶的緊張局勢。
- The waviness is mainly depending on the belt tension. 該波紋是主要依靠皮帶張力計。
- belt tension adjusting facility 皮帶張力調節設備
- Fine tension adjustment with eccentric gear. 偏心齒輪式張力微調。
- If thread is wound unevenly, move winder tension adjust base 3 to the right.or left until it is correctly positioned. 繞線時，請左右移動繞線張力桿座3，設定到正確的繞線位置。
- For belt tension specifications, refer to Specifications-Accessory Drive Belt in this group. 關于皮帶張力規格表，請參見本單元的規格表-輔助驅動皮帶
- If thread is wound unevenly, move winder tension adjust base 3 to the right or left until it is correctly positioned. 繞線時,請左右移動繞線張力桿座3,設定到正確的繞線位置。
- The lab test result shows that this system is feasible for dynamic test of belt tension. 系統能實現輸送帶靜止及運動過程中的沿線張力測試。
- The tension adjuster is an important equipment in the transport system atthe work line of electron beam radiation cross-linking wire and cable torealize the velocity synchronism. 張力調節裝置是電子束輻照交聯電線電纜生產線傳輸系統實現速度同步的關鍵部件。
- Some movement of sprockets and timing marks as belt tension is adjusted is normal. 當調整皮帶張力時，鏈輪與正時記號有些許移動是正常的。
- Usually the same belt drives the alternator, and belt tension is adjusted by swinging the alternator on its mounting. 通常將一臺機器的皮帶換到另一臺機器的時后，帶的張緊力需要通過調節安裝來調節。
- Loosen the accessory drive belt tension and remove the belt from the power steering pump (refer to Group 07, Cooling Systems for proper procedures). 放松輔助驅動皮帶，從動力轉向泵上拆下皮帶（有關程序，請參閱單元07，冷卻系統）。
- End Cap: Belt Tensioning System, easy access, easy adjustment. 完第：皮帶張緊系統，方便，調整方便。
- If this is not the case, the bearing must be subjected to an additional radial load, e. G. By increasing belt tension or idling torque, or by other means. 否則必須給軸承施加徑向載荷,例如,通過提高皮帶張力或空轉扭矩,或采用其他手段。
- Based on PLC,the closed loop control system design with transducer timing and the tension adjust by PID,can satisfy the craft of the full-automatic production request of the paper core consecution. 基于PLC具有PID調節的變頻調速和張力調節閉環控制系統設計方案,能滿足紙芯連續全自動生產的控制要求。
- Back off tensioner adjusting nut to create slack in cables. 旋下拉伸器調整螺帽使鋼纜松弛。
- In this paper the author discusses calculation of belt tension and selection of mo-tor power of sandwich belt conveyor with large inclination,conditions at which the two motorsrun synchronously. 討論了大傾角壓帶式輸送機輸送張力的計算、電機功率的選擇及兩電機同步運行的條件。
- According to the belt tension analysis of the large near-horizontal and upstroke conveyor during braking and starting,this paper gives the effects of brake location on the take-up tension. 通過近水平和上運大型帶式輸送機制動工況和起動工況的張力分析,明確了制動裝置位置對輸送帶張緊力的影響,進而提出大型輸送機制動與張緊裝置的優化布置方法。
