您要查找的是不是：
- bellows type pneumatic suspension 氣囊式空氣懸掛
- reversible sleeve piston type pneumatic spring 雙向筒形活塞式空氣彈簧
- reversible diaphragm piston type pneumatic spring 雙向膜片活塞式空氣彈簧
- Pressure gauges shall generally be bourdon tube or bellows type. 現場壓力表應通常是波登管或波紋管型。
- Only valves such as packless diaphragm or bellows type should be used. 只能使用無襯墊膈膜閥或波紋管閥。
- We proposed a dynamic counteracting method by means of the pneumatic spring to counteract on the centrifugal force. 為了消除這種影響,本文提出了一種使用空氣彈簧來抵消離心力影響的動態補償方法。
- Single convolution bellows type air spring 單曲囊式空氣彈簧
- Double convolution bellows type air spring 雙曲囊式空氣彈簧
- A new design method for pressure control system, including the flow force of nozzle-flapper type pneumatic servo valve, is proposed. 摘要提出了考慮氣動伺服閥流體力的精密壓力控制系統設計的新方法。
- Three convolution bellows type air spring 三曲囊式空氣彈簧
- We also manufacture KQL quick type pneumatic pump filters, especially GQL self-scrape-clean filters which have reached advanced international level. 配套產品有KQL快開式氣動隔膜泵過濾機及具有國際先進水平的GQL刮除清理式過濾機。
- The key factors affecting the stagnation point position of L-type pipeline section are the setting position of bellows type expansion joint and the bend angle degree. 影響水平轉角管段駐點位置的主要因素為波紋管補償器設置位置、彎頭角度。
- Pilot operated valves shall be considered for back pressures greater than 40% of set pressure if more favourable de-rating factors result in a valve smaller than a bellows type. 如果更多有利的非測定因子導致閥門小于波紋管類型的，對于背壓大于設定壓力的40%25的，應考慮輔助操作閥。
- Shaft sealing adopts single (double) face, bellow type mechanical seal, it also can adopt soft packing, is can meet sealing demands of all kinds of conditions. 軸封采用單（雙）端面、波紋管等形式的機械密封，也可采用軟填料密封，能適應各種條件下的密封要求；
- In this article, the author discussed the construction and running principle of the new type pneumatic wrench, expounded the design and manufacture essentials of this type pneumatic wrench. 論述了新型風扳機的結構及工作原理,闡明這種風扳機的設計制造要點,同時說明該種風扳機性能及制造的優缺點。
- Pneumatic Spring of Two Chambers Structure 兩室結構氣彈簧
- The calculation of stagnation point position of straight pipeline section with both movable ends and L-type pipeline section with bend at one end and bellows type expansion joint at other end is discussed. 摘要探討了兩側為活動端的直管段及一側活動端為彎頭，而另一側活動端為波紋管補償器的水平轉角管段駐點位置的計算。
- Model YQ Compressive Pneumatic Springs Seai the hogh-compressed air in the cyinder and produce eiasic force on a piston. YQ型壓縮氣彈簧是一種將高壓氣體密封于缸筒內，通過活塞產生彈性功能的產口。
- Balanced bellows seals may be required instead of conventional type due to process fluid considerations. Pilot operated valves are acceptable in place of bellows type for clean services. 出于對工藝介質的考慮，平衡波紋管密封可能要求替代常規類型。對于潔凈用途，允許用輔助操作閥替代波紋管類型。
- Some improvements for mechanical seals on mid-pressure ammonia pumps in our plant is summarized,A performance contrast is analysed and some application recommendations are given in future service preferentially for the metal bellow type mechanical seals. 結合某中壓熱氨泵的機械密封改造 ,對金屬波紋管機械密封與普通機械密封的性能對比進行了分析 ,指出金屬波紋管機械密封可以在很多工況下取代使用 ,輔助密封圈的普通機械密封。
