您要查找的是不是：
- To prevent unnecessary battery depletion. Set the main switch selector to L (lock) when you are not using the camera. 為避免不必要的電池耗電,當您不用相機時,請把主選擇開關設定到L（鎖定）。
- Set the main switch selector to A (auto). 把主選擇開關調至A(自動)。
- Before disassembling battery and disconnect main switch of the battery, make sure ignition switch has been turned off. 拆卸蓄電池和斷開蓄電池主開關之前，確認點火開關已關閉。
- No power even when the main switch is turned on. 即使總開關打開了也沒有電。
- Switch off the system at the main switch of the tablet press. 壓片主開關關閉系統。
- Set the main switch selector to the desired operation. 設置主選擇開關在所需的操作狀態。
- Set the main switch selector to A (auto) or M (manual). 把主選擇開關轉到A(自動)或M(手動)
- The jitter of the main switch is less than 1. 5ns(RMS ). Blumlein主開關工作電壓大于280kV;抖動小于1.;5ns(均方根值)。
- MCCB &MCB can be equipped for main switch and sub switch. 箱內可裝主進線塑殼開關及分回路微斷開關。
- The heater is now ready for operation and the main switch can be closed. 然后這時熱水器可以重新工作,可以重新打開電源開關。
- Set the main switch selector to A and set the mode dial to normal mode. 把主選擇開關設置在A(yíng)（自動）,同時把模式盤設置在普通模式。
- The tablet press is switched off at the main switch. 關閉壓片主開關。
- Each unit should include a main switch and ammeter with a scale of about 20 ampere capacity. 每一套裝置應包括一個主開關和電流表，電流表的刻度范圍約20安培。
- Main switch selector: Sets the camera to L (lock: power is turned off), and A (Auto), or M (Manual) operation. 主開關選擇器:設置相機在L(鎖定:電源斷開),A(自動)或M(手動)操作。
- When then main switch selector is set to A (auto) or M (manual), the film will resume rewinding. 當主選擇開關調至A(自動)或M(手動)時,又會(huì )恢復倒片
- The main switch selector, mode dial, up\down buttons, and a brief explanation of their functions are shown below. 以下說明主選擇開關、模式盤、向上\\向下按鈕以及解釋它們的功能。
- The main switch selector, mode dial, updown buttons, and a brief explanation of their functions are shown below. 以下說明主選擇開關、模式盤、向上向下按鈕以及解釋它們的功能。
- To cancel AE lock before releasing the shutter, press the previewAE lock button again or set the main switch selector to L (lock) to turn off the power. 如要在快門釋放前取消自動曝光鎖定,請再次按壓預景深自動曝光鎖定按鈕,或把主選擇開光調到L,以斷開電源。
- The following modes will be canceled when the main switch selector is set to L (lock) AE lock setting (in the previewAE lock user setting mode). Self-timer mode. 當主選擇開關設置在（鎖定）,以下的模式將被取消。自動曝光鎖定設置（在預景深自動曝光鎖定設置模式）,自拍模式。
- Switch on the system at the main switch of the tablet press and wait until the system is booted up to the starting mask. 按下壓片系統上的壓片主開關,等待直到界面引導系統啟動。
