您要查找的是不是：
- Remove differential case from axle housing. 從軸管上拆卸差速箱。
- Remove differential case and dummy bearings from axle housing. 拆卸軸殼內的差速箱和平衡軸承。
- Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts. 在軸殼內（沒有墊片）安裝差速箱和模型軸承，并緊固固定帽螺栓。
- The analysis provides a reliable reference for the optimal design of a hydro-bulged axle housing. 研究為液壓脹形橋殼優化設計提供可靠的參考。
- The strength, stiffness and mode shape of the rear axle housing was calculated via finite elemant methool (FEM). 根據計算結果分析，指出了其結構存在的缺點，提出了改進方案。
- The analytical findings provide some referential basis for the designof a rear axle housing structure. 研究結果為橋殼結構設計提供了一定依據。
- In order to reduce gas hole defects in the rear axle housing castings,oddside venting system was used. 為解決汽車后橋外殼鑄件存在的氣孔缺陷,采了假型排氣系統。
- Drive shafts modified for new location on the axle housing and because of the new doubler. 傳動軸修改來配合分動箱放大齒輪組。
- The first axle housing type is a unitized carrier construction, commonly referred to as a Salisbury or Spicer type axle assembly. 第一橋殼型是一個單元載體建設，通常稱為梳士巴利或斯派塞類型橋總成。
- There are 12 round holes circumferencially equispaced on the axle housing cast,being in need of radial multiple core pulling. 軸套鑄件上有12個周向均布的圓孔,壓鑄生產時需要多型芯徑向抽芯。
- Unitized carrier axle housing constructions of this type are economical to manufacture and are readily adaptable for a variety of vehicles. 組合承運人車軸住房建設這類經濟生產，并易于適應各種車輛。
- Through the drive axle housing , the tractive force 、 braking force and lateral force act on the wheel transfer to the suspension system 、 frame or carriage. 作用在驅動車輪上的牽引力、制動力和側向力,也是經過橋殼傳到懸掛及車架或者車身上。
- Aiming at laggard and low automatization degree of clearance measure method on axial assembly clearance between half shaft assembly and rear axle housing in automotive rear axle assembly, a new type clearanceometer was developed. 針對汽車后橋總成中半軸總成與后橋殼之間軸向裝配間隙測量方法落后、動化程度差等問題,開發了汽車后橋總成裝配間隙測量?jì)x。
- The 194 Rear Beam-design Iron (RBI) axle housing has an iron center casting (differential housing) with axle shaft tubes extending from either sidThe tubes are pressed into and welded to the differential housing to form a one-piece axle housing. 194后梁設計鋼（RBI）軸殼有一個帶有驅動軸套的鋼制的中心鑄件（差速殼），它延伸到兩邊。軸套被壓進差速殼，并焊在差速殼上，形成了一個整體的軸殼。
- Main products are gray cast iron, ductile cast iron, carbon cast steel for construction machinery and high-load automobile with the no-bake resin sand process, such as axle housing, gearbox housing, hub, carrier etc. 本公司主要采用生產無箱樹脂砂工藝生產工程機械、重型汽車用的鑄鋼件、鑄鐵件、球墨鑄鐵件、如橋殼、變速箱、輪轂、托架等鑄件。
- The allowable strength, static strength, fatigue life and load-carrying capability of hydro-bulged rear axle housing in a 0.75 t truck are analyzed using FEA software ANSYS and the variation rule of its strength is obtained. 摘要以0.;75t貨車液壓脹形橋殼為例，利用有限元分析軟件ANSYS對其許用強度、靜強度、疲勞強度（壽命）及其承載能力進行分析，得到液壓脹形橋殼強度的變化規律。
- The axle housings for a0 75 ton automobile was tested and the technological parameters were given for sinking the end part and hydr... 對0.;75t輕型車液壓脹形橋殼進行了試驗研究。
- Using the programmable controller in the automobile rear axle house ring stiffener,logic sequential control was realized in the top plate automatic welding craft. 采用可編程控制器在汽車后橋殼加強環、后蓋自動焊接工藝中實現邏輯順序控制。
- The back axle of the bus was broken. 公共汽車的后軸斷了。
- New Process of Hot Extrusion for STEYR Axle Housing 斯太爾軸頭熱擠壓新工藝
