您要查找的是不是：
- Electric field of the emission system of a liquid metal ion source was simulated, based on the conventional dynamic protrusion model and the widely used charge simulation method. 摘要發射系統是液態金屬離子源的關鍵部件之一，它的性能的優劣直接影響到整個離子源的工作穩定性和可靠性。
- The liquid metal flow during mould filling in bottom gating system and its influence on the casting quality are introduced emphatically. 著重介紹了液態金屬在底注式澆注系統充填型腔時的流動，以及其對鑄件質量的影響。
- Bright Dipper Metal System Manufacturing (Shanghai) Co., Ltd. 博罡金屬系統制造(上海)有限公司。
- Intense, glowing copper! Applied wet it's like liquid metal. 強烈的銅色!濕用時像是液態金屬。干用時是古銅帶銀的亮片。
- Abstract: The main factors influencing mould-filling of evaporated pattern casting,including foamed plastic pattern(white pattern),coating,dry sand,vacuum degree,liquid metal,pouring system,foundry method et al,was introduced. 文摘:介紹了影響消失模充型的主要因素：白模、涂料、干砂、負壓、金屬液、澆注系統、工藝因素等。
- Mercury, the liquid metal that is used in many thermometer, is very much heavier than water. 許多溫度計中應用的液體金屬--水銀比水重得多。
- To form(liquid metal,for example) into a particular shape by pouring into a mold. 鑄造通過把（如金屬熔液）注入一個模具，使它具有一個特殊形狀
- A current is sent transversely through the liquid metal, in a direction at right angles to a transverse magnetic field. 使電流橫穿過液態金屬，其方向又與橫向磁場垂直。
- Words and Expressions cast vt. To form (liquid metal, for example) into a particular shape by pouring into a mold. 鑄造;通過把(如金屬熔液)注入一個模具,使它具有一個特殊形狀。
- To form(liquid metal, for example) into a particular shape by pouring into a mold. 鑄造通過把（如金屬熔液）注入一個模具，使它具有一個特殊形狀
- The MHD effect on liquid metal free surface jet flows under magnetic field has been investigated. 摘要分析了磁流體力學效應對液態金屬自由表面射流穩定性的影響。
- The solidification process of liquid metal in the CASTEX technique was studied by FEM(finite element method). 利用有限元法研究了連續鑄擠工藝中液態金屬的動態凝固過程。
- Abstract: The solidification process of liquid metal in the CASTEX technique was studied by FEM(finite element method). 摘 要: 利用有限元法研究了連續鑄擠工藝中液態金屬的動態凝固過程。
- The methods of denitrogenation from liquid metal by flux, vacuum and bubble carrying are reviewed in this paper. 本文綜述了金屬液熔渣脫氮、真空脫氮和氣泡攜帶法脫氮方法。
- We design a light metallic system which permits ample overhangs, freeing up the interior space from other structural elements or walls. 設計者為其設計了高懸的輕的金屬系統，使其內部空間和其他的結構以及墻體分離。
- We design a light metalic system which permits ample overhangs, freeing up the interior space from other structural elements or walls. 設計師設計了一個輕金屬系統，允許懸垂，釋放了室內空間和其他結構元素以及墻體。
- Abstract: Porosity of die castings caused by air entrapped into the liquid metal in the shot sleeve is common problem of die csating process. 文摘:壓室中氣體卷入金屬液內而造成壓鑄件內部氣孔是壓鑄過程常見的問題。
- But when it comes to using the turbulent flow of liquid metal rather than well-behaved cables and wires, the experiment becomes rather harder. 但當要用劇烈流動的液態金屬來代替性能良好穩定的電纜和金屬線圈時，這個實驗就變得相當困難。
- Expansion and contraction is greater in thermoplastic systems than in metal systems. 熱塑性塑料系統的膨脹和收縮比金屬系統更加明顯。
- As a result, liquid metal in a PM experiences radial and tangential forces that are cyclically variational both in direction and magnitude. 結果表明:液態金屬在永磁體攪拌過程中,受到大小和方向周期變化的徑向力和切向力;
