您要查找的是不是：
- angular contact radial ball bearing 角面接觸徑向滾珠軸承
- Rolling bearings; angular contact radial ball bearing; double row, with spacer balls 滾動軸承。分離式雙列徑向向心推力球軸承
- When the load is made up of radial and axial components which are almost equal in magnitude, an angular contact spherical plain bearing (fig 10) should be chosen. 當負荷由大小幾乎相等的徑向和軸向分力組成時,應選擇角接觸球面滑動軸承(圖10)。
- Actual deviation of width of the angular contact spherical plain bearing. 角接觸關節軸承實際寬度偏差。
- Two matched angular contact bearings provide good radial and thrust capabilities. 兩同樣角接觸滾珠軸承等,可提供很好徑向力和推力。
- radial angular contact ball bearing 徑向角面接觸滾珠軸承
- Note that an angular contact bearing can be disassembled axially and so can easily be filled with a full complement. 后經醫生治療，體征有了改變，雖然已經結了婚，但不能生育。這多么令人遺憾！
- An angular contact ball bearings uses axially asymmetric races. 在有了一定的工作經驗以后，可以去考注冊建造師。
- The analytical model of stiffness for angular contact ball bearing of aeroengine is established by the quasistatic analytical method. 通過擬靜力學分析方法，可以建立航空發動機角接觸球軸承的剛度分析模型。
- On the basis of traditional quasistatic analytical method, stiffness for angular contact ball bearing of aeroengine is studied. 在傳統擬靜力學分析方法的基礎上,對航空發動機角接觸球軸承剛度進行了研究。
- Using the Hertz contact deformation theory, the min. rib height of angular contact ball bearing under axial load and controlled contact stress is calculated. 利用赫茲的接觸變形理論 ,對角接觸球軸承的套圈最小擋邊高度在承受軸向載荷、控制接觸應力的情況下進行了理論計算 ,并給出了計算公式。
- An indirect method was introduced to measure raceway diameter of angular contact ball bearing using hori- zontal length measuring machine, steel ball and measuring block. 量塊檢定一般采用比較法測量,對于非標準長量塊的測量現在可以利用萬能激光測長機進行測量。
- Deep groove ball bearing, insert bearing, angular contact ball bearing, four-point contact ball bearing, thrust bearing, automotive wheel bearing, needle roller bearing, bottom roller bearing for textile machinery etc. 深溝球軸承、調心球軸承、外球面軸承、角接觸軸承、四點角接觸軸承、推力軸承、汽車輪轂軸承和汽車專用軸承、滾針軸承和紡織專用下羅拉軸承等。
- The boundary dimensions of SKF double row angular contact ball bearings are in accordance with ISO 15:1998, except for the width of bearing 3200 A. SKF雙列角接觸球軸承的外形尺寸符合ISO 15:1998標準,軸承3200A的寬度除外。
- All other radial bearings can accommodate some axial loads in addition to radial loads; see "Combined load". 所有其它的徑向軸承除了徑向負荷外,還可承受一些軸向負荷;請參看“混合負荷”。
- In order to increase rigidity and rotation accuracy,to control the revolution and rotation slip of the rolling elements,the certain preload should be applied on a high speed angular contact ball bearing. 提高主軸剛性和旋轉精度 ,控制滾動體的公轉和自轉打滑 ,應對高速精密角接觸球軸承施加一定的預緊載荷。
- Angular contact ball bearings for ball screws - Series - Boundary dimensions - Classification, tolerance. 滾珠絲杠用角面接觸球軸承。系列。外形尺寸。分類和公差。
- It is assumed that the load is constant in magnitude and direction and is radial for radial bearings and axial, centrically acting, for thrust bearings. 假定載荷大小和方向不變,對徑向軸承而言為徑向載荷,對推力軸承而言為作用于中心的軸向載荷。
- This article explains mainly installation form of angular contact ball bearing and its axial backlash influence in practical application, and introduces the corresponding counter-measure. 本文主要闡述了角接觸軸承的安裝形式及其軸向游隙在實際應用中的影響,并介紹了相應的應對措施。
- Single and double deep groove ball bearings, single and double angular contact ball bearings and various non-standard bearings. 單雙列深溝球軸承,單雙列角接觸軸承及各種非標軸承。
