您要查找的是不是：
- Repeat steps2-5 until proper sag is achieved, then replace the air valve cap. 重復2－步驟以達到最佳預壓行程后，蓋上氣閥嘴帽。
- Repeat steps 2-5 until proper sag is achieved, then replace the air valve cap. 重復2－5步驟以達到最佳預壓行程后，蓋上氣閥嘴帽。
- Locate the Schrader air valve on the shock and remove the air valve cap. 找到避震上的美嘴氣閥，取下氣閥帽。
- If multiple ETX/ETSX tanks are installed in the system, check pressure of each for possible air leaks. Be sure air valve caps are on tight. 如果在系統上安裝了多個ETX/ETSX膨脹罐，則檢查每個膨脹罐，看看是否有氣體泄漏。確保塑料氣體閥門蓋是否擰緊。
- Replace the cylinder outlet seal and valve cap. 替換鋼瓶排氣口密封和閥門帽。
- air valve cap 氣閥蓋
- Therefore, the radiator cover is equipped with air valve, and has a public blowhole links the atmosphere. 在使用中應保證此孔暢通，不能堵塞或失去其功能，否則會(huì )影響散熱器和發動機的散熱性能。
- Smooth operation of throttle linkage and throttle body air valve. 節流連桿和節流體空氣閥的平穩操作。
- Unthread the pump from the air valve and measure sag. 參考氣壓設定建議數值表打入相應氣壓以達到所需的預壓行程。
- Equipped with air valve to ejecting the products by blowing. 配備吹氣裝置以便于脫模。
- Unscrew the Allen screw in the middle of valve cap and lift up the cap just enough to pick up the old diaphragm. 旋松閥帽中間的內六角螺絲，并且提起閥帽，正好足夠拿走舊閥膜。
- All parts inside adopt the stainless steel, and are installed on the valve cap, maintenance is convenient. 內部零件全部采用不銹鋼制造，并且安裝在閥蓋上，維修保養極為方便。
- Insulting filling and fibre sets of various industrial furance such as cap cover furnace,heating furnace,heat treatment furnace,shuttle furnce, roller conveyer furnace,cracking furnace,enamel furnace. 各種工業爐窖如罩式爐、加熱爐、熱處理爐、梭式窖、隧道窖、輥道窖、裂解爐、搪瓷窖隔熱層填料、纖維組件。
- Do not overheat cylinders to increase pressure or discharge rate. NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. 禁止使鋼瓶過熱來增加壓力或流速。禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽地開口處。
- NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. Doing so may damage the valve causing it to leak. 禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽的開口處。這樣做可能損傷閥門，導致泄漏。
- NEVER insert an object (e. G., Wrench, screwdriver, pry bar, etc.) Into valve cap openings. Doing so may damage the valve causing it to leak. 禁止把物體(如扳手、螺絲起子、撬桿等)插入閥門帽的開口處。這樣做可能損傷閥門,導致泄漏。
- NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. Doing so may damage the valve causing it to leak . 禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽的開口處。這樣做可能損傷閥門，導致泄漏。
- An overall air control for each pipe in each room is available by fitting an air valve at the hot water supply. 把空氣閥安裝在溫水供給器時可綜合處理各房間管路內的空氣。
- Technician was adjusting air valves on pallet elevator behind the safety guard. 該技工實際上是在調整安全裝置后面的托盤貨物升降機的氣閥。
- Screw the FOX Racing Shox High Pressure Pump onto the air valve until the pump shows pressure on the gauge. Do not over-tighten. 把避震專用打氣筒旋緊在氣閥上直到避震氣筒上的壓力表有氣壓顯示，不要過份旋緊。
