您要查找的是不是：
- ASRV Air Switching Relief Valve 空氣轉換減壓閥
- Hang the Air Gap Drain on the body of the relief valve (Fig. 2). 將氣隙排放裝置懸掛在安全閥閥體上（圖2）。
- Remove the elbows from the relief valve base. 從安全閥底座拆卸彎頭。
- Clean or replace the relief valve seat. 清洗或更換安全閥閥座。
- Damage or fouled relief valve seat. 安全閥閥座損壞或受到污染。
- Damaged or fouled relief valve seat. 安全閥閥座受到損壞或污染。
- Relief valve must be piped to a suitable drain. 安全閥必須配置通向適當排泄口的排泄管道。
- Install relief valve cover nut and tighten. 安裝安全閥閥蓋螺母,并加以緊固。
- Reinstall the elbow into the base of the relief valve to hold the Air Gap Drain in place. 將彎頭安裝在安全閥的底座,將氣隙排放裝置固定住。
- The installation of a Watts air gap with the drain line terminating above a floor drain will handle any normal discharge or nuisance spitting through the relief valve. 安裝帶著排放管道的美國瓦茨氣隙，其排放管道的終端位于地漏的上方，用于處理通過安全閥的任何正常排放或有害噴濺。
- To assemble the Relief Valve Assembly have a screwdriver ready. 準備好組裝安全閥總成的螺絲刀。
- Place the relief valve seat back into the chamber bore. 將安全閥閥座放回到鏜孔內。
- Remove the relief valve hose from fitting below inlet ball valve. 從進口球閥下面連接件拆卸安全閥軟管。
- ASDV Air Switching Diverter Valve 空氣轉換分流閥
- Slide the diaphragm assembly into the relief valve seat. 將隔膜總成滑進到安全閥閥座內。
- There are fulse, kilowatt-hour meter,air switch and other elements,there are lead sealing holes on each metering space doors so as to provide sealing electric. 箱內裝有熔斷器、電度表、空氣開關等元件，計量室門上均有鉛封孔，能有效防止竊電。
- No valve is to be placed between the relief valve and tank. 在熱水器儲水罐和安全閥之間不需要安裝任何閥門。
- Air switch, contactor and thermo switch all adopt Schneider series products.Other appliances, such as relay, button switch, and indicator must use national famous products. 空氣開關、接觸器、熱繼電器均采用施耐德系列產品，其它繼電器、按鈕開關、指示燈等電器均采用國內名優產品；
- First to shut off air switch, open power resource switch, then start cyclone fan and electric heater, and check to insure no creepage then heat the drum. 首先合上空氣開關，打開總電源以開關，隨后開啟離心風機，開啟所需功率的電加熱器，并檢查是否漏電，如正常，即進行筒身預熱。
- Electrolysis of relief valve seat or first check seats. 安全閥閥座或第一止回閥閥座被電解或電蝕。
