您要查找的是不是：
- Remove valve spring and retainer. 拆卸閥彈簧和扣件。
- CAUTION: The check valve spring is in compression. 警告：止回閥彈簧處于壓縮狀態。
- The pressure of scraper is controlled by the air pressure adjusting valve. 配套氣壓調節閥,控制刮印刀的壓力。
- For removal of valve stem seal and lower valve spring guide. 可用于拆卸汽門油封或降低汽門彈簧。
- Consisting of PVC tube,air-balloon,adjusting valve and stainless steel needle. 產品由PVC軟管、氣囊，調節閥，不銹鋼針組成。
- Non-contacl device. squeegee/flood bar independent pressure adjusting valve. 刮刀墨刀印刷壓力獨立調壓閥/起網裝置等.
- "Four-spring" spring for the piston, tappet (wheel) spring, into the oil valve spring Valve spring weakened or broken springs flexibility to replace or add to timely adjust pad. “四簧”為活塞彈簧、挺桿(滾輪)彈簧、進油閥彈簧、出油閥彈簧，彈簧彈性減弱或折斷要及時更換或加墊調整。
- The one-way adjusting valve of liquid current is effectively controlled riveting speed. 油路加裝單向調節閥,有效控制鉚接速度。
- The output signal of the turbine host controls was delivered to DEH for adjusting valve position. 汽機主控輸出信號送DEH,控制調門開度。
- The system consists of feedwater pump control, adjusting valve level control, safety and alarm devices. 該系統包括給水泵控制、調節閥閥位控制以及安全保護和報警。
- Due to the release of pressure when removing the cover, the relief valve spring may eject quickly. 因為在拆卸閥蓋時松開壓力，安全閥彈簧可能會(huì )快速彈出來。
- The corrosion of intermedium on fluid patrs of adjusting valve during the prodution of phenol is described briefly. 簡要敘述了苯酚生產過程中介質對調節閥節流件的腐蝕,分析了介質濃度、溫度對材料耐腐蝕性能的影響。
- Multi - purposed optimal design of reliability for valve spring based on fuzzy method. 基于模糊學方法的氣門彈簧可靠性多目標優化設計。
- So the vital problem of the combustion organization was translated into how to control the aperture of the adjusting valve properly. 于是燃燒組織問題轉化為對該調節閥的開度如何施加適當控制的問題。
- Remove the relief valve cover, stem/diaphragm assembly, and relief valve spring. 拆卸安全閥閥蓋，閥桿/隔膜總成，和安全閥彈簧。
- Vacuum table side in &out, easy for printing substrate place.Non-contact device, squeegee/flood bar independent pressure adjusting valve. 平面吸風抬面自動進退;放置印刷工作物更容易，刮刀墨刀印刷壓力獨立，調壓閥/起網裝置等.
- Install a dial indicator so plunger contacts valve spring retainer as nearly perpendicular as possiblZero the indicator. 安裝一個表盤式指示器，使柱塞與氣門彈簧護圈盡可能垂直。將指示器調零。
- Adjust valve opening manually or automatically，to change the resistance force of pump discharge pipline, and make the flowrate steady as expected. 手動或者自動調節控制閥開度，改變泵輸出管線的阻力，使流量穩定在期望值。
- Check whether or not the fuel injection pump plunger and fuel outlet valve is worn or clogged, plunger spring and fuel outlet valve spring is broke. 噴油泵柱塞及出油閥是否磨損或卡死、柱塞彈簧及出油閥彈簧是否折斷；
- Then, pneumatic valve spring made from this spring steel wire have been treated by this investigation of liquid tufftriding process. 然后 ,用以對此規格的鋼絲制造的氣閥彈簧進行了低溫液體軟氮化處理。
