您要查找的是不是：
- regulating valve cap nut 調節閥螺母
- Replace the cylinder outlet seal and valve cap. 替換鋼瓶排氣口密封和閥門帽。
- Repeat steps2-5 until proper sag is achieved, then replace the air valve cap. 重復2－步驟以達到最佳預壓行程后，蓋上氣閥嘴帽。
- Repeat steps 2-5 until proper sag is achieved, then replace the air valve cap. 重復2－5步驟以達到最佳預壓行程后，蓋上氣閥嘴帽。
- The pressure of scraper is controlled by the air pressure adjusting valve. 配套氣壓調節閥,控制刮印刀的壓力。
- Locate the Schrader air valve on the shock and remove the air valve cap. 找到避震上的美嘴氣閥，取下氣閥帽。
- Consisting of PVC tube,air-balloon,adjusting valve and stainless steel needle. 產品由PVC軟管、氣囊，調節閥，不銹鋼針組成。
- Non-contacl device. squeegee/flood bar independent pressure adjusting valve. 刮刀墨刀印刷壓力獨立調壓閥/起網裝置等.
- I have suggested TSM buy the weld nut from USA(just like the cap nuts) to save time in finding a repair. 我已經建議TSM從美國采購焊接螺母（與這種螺帽很類似）以節省修理時間。
- Unscrew the Allen screw in the middle of valve cap and lift up the cap just enough to pick up the old diaphragm. 旋松閥帽中間的內六角螺絲，并且提起閥帽，正好足夠拿走舊閥膜。
- The one-way adjusting valve of liquid current is effectively controlled riveting speed. 油路加裝單向調節閥,有效控制鉚接速度。
- All parts inside adopt the stainless steel, and are installed on the valve cap, maintenance is convenient. 內部零件全部采用不銹鋼制造，并且安裝在閥蓋上，維修保養極為方便。
- The output signal of the turbine host controls was delivered to DEH for adjusting valve position. 汽機主控輸出信號送DEH,控制調門開度。
- The system consists of feedwater pump control, adjusting valve level control, safety and alarm devices. 該系統包括給水泵控制、調節閥閥位控制以及安全保護和報警。
- Do not overheat cylinders to increase pressure or discharge rate. NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. 禁止使鋼瓶過熱來增加壓力或流速。禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽地開口處。
- The corrosion of intermedium on fluid patrs of adjusting valve during the prodution of phenol is described briefly. 簡要敘述了苯酚生產過程中介質對調節閥節流件的腐蝕,分析了介質濃度、溫度對材料耐腐蝕性能的影響。
- NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. Doing so may damage the valve causing it to leak. 禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽的開口處。這樣做可能損傷閥門，導致泄漏。
- NEVER insert an object (e. G., Wrench, screwdriver, pry bar, etc.) Into valve cap openings. Doing so may damage the valve causing it to leak. 禁止把物體(如扳手、螺絲起子、撬桿等)插入閥門帽的開口處。這樣做可能損傷閥門,導致泄漏。
- So the vital problem of the combustion organization was translated into how to control the aperture of the adjusting valve properly. 于是燃燒組織問題轉化為對該調節閥的開度如何施加適當控制的問題。
- NEVER insert an object (e.g., wrench, screwdriver, pry bar, etc.) into valve cap openings. Doing so may damage the valve causing it to leak . 禁止把物體（如扳手、螺絲起子、撬桿等）插入閥門帽的開口處。這樣做可能損傷閥門，導致泄漏。
