您要查找的是不是：
- The white corrosion products on hot dip Zn Al alloy coating exposed to seawater in dynamic aerated immersion were investigated by means of XRD and TEM. 采用XRD和TEM對熱浸鋅鋁合金鍍層在動態充氣海水全浸試驗時所形成的白色腐蝕產物進行了研究。
- T2 Cu/2A50 Al alloy was bonded by blacksmith diffusion welding technology. 采用鍛接擴散焊法進行了T2銅/2A50鋁合金異種材料的焊接。
- The vacuum differential-pressure casting (VDPC)technol ogy for thin-wall ed Al alloy was introduced. 介紹了用于薄壁鋁合金鑄件的真空差壓鑄造工藝。
- The stress-strain date and curve were obtained from the isothermal compression experiment of 7A04 Al alloy. 根據等溫壓縮實驗得出7A04鋁合金應力-應變數據,擬合出材料溫成形應力-應變曲線。
- This paper discussed the idea of the gas atomization Mg and Mg - Al alloy powder by supersonics high ptire N2 gas. 介紹了用超音速高純氮氣流來生產氣霧化鎂和鎂鋁合金粉的設想。
- PM high strength Al alloy is very important light weight material in automobile. 粉末冶金高強度鋁合金是重要的汽車輕量化材料。
- Ce conversion film was obtained on surface of Al alloy LY12 by immersion process. 利用浸漬法在鋁合金LY12表面上獲得了稀土轉化膜。
- Keys to technology and die design of stamp-ing of Al alloy profile have been introduced. 介紹了鋁合金型材在沖壓加工時的工藝特點和模具設計要點。
- The friction and wear properties of 2 kinds of high strength Zn Al alloys and 3 kinds of Cu alloys are demonstrated. Under different lood and rotative velocity, the friction factor and abrasion wear of the alloys and their coupling samples are given. 采用MM200磨損試驗機，測定和對比了鑄造鋅鋁合金（ZZnAl27Cu2A和ZZnAl27Cu2D）和工業上常用銅合金（ZCuSn6Zn6Pb3，ZCuA110Fe3和ZCuZn33Mn2Pb2）的摩擦磨損特性。
- EPMA analysis shows that ZnBTA can also inhibit the absorption/aggre-gation process of Cl~- on the sample surface of Al alloy. 電子探針?lè )治鼋Y果證明,ZnBTA 可以阻滯 Cl~-在鋁合金表面的吸附聚集過程。
- Abstract Furan resin sand is poor in collapsibility when it is used for Al alloy casting,specially for some large、thin section castings. 呋喃樹脂砂用于鋁合金鑄造時，特別是對于一些大型、薄壁鋁合金鑄件，型芯的潰散性較差。
- The industrial practical crystallizer for Al alloy in low-frequent electromagnetic casting was designed based on the above mentioned idea. 結合生產實際情況,設計出工業上實用的低頻電磁鑄造鋁合金結晶器。
- The worn surface morphologies of the composites and the Al alloy matrix were observed with a scanning electron microscope. 復合材料具有低的磨損率和穩定的摩擦因數,因此具有良好的耐磨性。
- This type of material includes Al alloy and Al-based composite, and recently the HSRS of Mg_based composite and Ti alloy is investigated. 高應變速率超塑材料主要是鋁基復合材料及鋁合金，最近，對鎂基復合材料、鈦合金高應變速率超塑性能的研究也已開始。
- The cutting force and machined surface quality during high speed milling a typical Al alloy C shape workpiece are experimental investigated. 對高速銑削典型鋁合金框架結構工件時的切削力和加工表面質量進行了試驗研究。
- In the paper,the technology and equipment of furnace brazing for AL alloy radiator are introduced.The property of brazed joint is analyzed. 介紹了一種鋁散熱器的釬焊工藝和設備，并對釬焊接頭性能進行分析。
- The authors studied the bright transform surface velamen of forging Al alloy LD10, chose the best technical dispensing and parameters. 對LD10鍛件的光亮轉化膜進行了研究,選出最佳工藝配方及參數。
- Results show that the hydrophilic membranes can meet the needs of Al alloy fins of air-conditioners with good properties mentioned above. 結果表明:其親水性、耐蝕性和耐熱性?xún)?yōu)良,能滿足空調鋁合金翅片的使用要求。
- An introduction was made on the national standard on the Al alloy wheel rim for automobiles and on the internal standard derived from it. 介紹了汽車鋁合金車輪輪輞的國家標準和由此衍生出來的內部標準,并介紹了低壓鑄造模具的標準化設計。
- The ballistic performance has been improved to reach the index demand by the adjustments of 7A52 Al alloy composition and heat treatment. 通過對7A52鋁合金成分與熱處理工藝設計調整,提高了抗彈性能,達到了防彈衣指標要求,并投入了小批量生產,現已裝備應
