您要查找的是不是：
- Give an introduction about a simple general-purpose bending die. 介紹了一種簡易通用彎曲模設計。
- The die of NC tube bending is composed of bending die,clamp die,wiper die,pressure die and mandril. 導管數控彎曲模具包括彎曲模、夾模、壓模、防皺模和芯棒。
- The symmetric wire bent elements of small-production and low-accuracy used the simplerevolving bending die to improve economical efficiency. 小批量、低精度和大尺寸的對稱式線材彎曲件，采用簡易繞彎模彎曲能提高經濟效益。
- Bend the wire so that it forms a 'V'. 把鐵絲彎成 V 形。
- The structure, operating principle and main design points of the hopper-type automatic-feeding bending die used on a general stamping mahine are stated. 介紹了在通用沖床上使用的漏斗式自動送料彎曲模的結構形式、工作過程和設計要點。
- The stream takes a sudden bend to the east. 小溪突然轉向東流。
- The paper analyzes processing technology of ploughshare of agricultural machinery plouogh, explains factors of spring back, and designs a set of hot bending die. 對農機犁上的鏵零件進行了加工工藝方案分析,闡明了回彈因素,并設計了一副熱彎曲模具。
- She bend over backwards to show it. 她拼命把他顯露出來。
- They refused to bend to the hijackers' demands. 他們拒絕屈從于劫機者的要求。
- Don't bend the wires down, it'll break them. 不要彎折那些線，會(huì )弄壞它們的。
- That sharp bend is a death-trap for motorists. 那個急轉彎是開汽車的人的死亡陷阱。
- Every winter some old people die from hypothermia. 每年冬天都有些老人死于體溫過低。
- Soon the truck come into sight around a bend and on an upgrade. 不一會(huì )卡車就出現在一個拐彎和上坡處。
- Abstract: The article describes the structure, work principle, design method of the tool parts and the calculation of the bending force of bending die with double roller for load bearing support. 文摘:介紹了承力隔架用“雙轉輥彎曲模具”的結構、工作原理、主要工作零件設計及其彎曲力的計算方法。
- The thesis introduces the key technology for development of bending die CAD system, including API of SolidWorks, the way of customization development, database and reusable component technology. 本文首先介紹了三維CAD及其相關技術，包括SolidWorks的應用編程接口，SolidWorks二次開發方法，數據庫技術，ActiveX技術和構件技術。
- A right-angled bend in a pipe or conduit; an elbow. 直角彎，肘導管或管道中的直角彎; 肘
- Bend a piece of iron into a horseshoe. 把一塊鐵彎曲成馬蹄形。
- Through designing the bending die for the Sanxia motor copper tube, discussed on the defects that prossibly appeared in the small radius bending tube, and proposed the preventive measure. 結合三峽電機銅管彎曲模具結構設計,對小半徑銅管彎曲過程中可能出現的缺陷進行了探討,提出了預防措施。
- It's dangerous to overtake on a bend. 在轉彎處超車十分危險。
- One of the runners got boxed in on the final bend. 一個賽跑者在轉最后一彎時被人擋住了。
