您要查找的是不是：
- Moreover, the duty cycle of the output clock is presettable. 除此之外，輸出時脈訊號的工作周期是可預先設定的。
- How should we establish duty cycle for the components, systems or products? 我們應該如何為零部件、系統或產品設立責任周期?
- Therefore duty-cycle corrector (DCC) is needed to correct duty cycle as 50%. 因此，我們需要工作周期校正器使得時脈的校正工作周期自動校正到50%25。
- Depending on how the device is triggered will also depend on whether the duty cycle is fixed or random. 根椐設備的觸發方式并且還要根椐占空比是固定或隨機。
- The resulting switchpoints are air-gap independent, greatly improving output accuracy and duty cycle. 設置后的開關點獨立于氣隙,可極大地改善輸出精確度和工作循環。
- With wide working voltage range can suit wire netting well.lts high duty cycle is applicable for continuous work in factory. 工作電壓范圍寬，電網適應能力強，負載持續率高，更適合工廠里連續工作。
- In general, the motor power rating, speed, torque, and details of the regenerative duty cycle need to be known. 一般而言,我們應該清楚電機的額定功率,速度,力矩和具體的制動周期。
- The duty cycle is higher compared to a 600V solution due to a higher reflected voltage of 390V. 漏源極電壓（圖28）在反射過程結束后并減小到100伏特時場效應晶體管導通。
- The duty cycle is lower compared to an 800 V solution due to a lower reflected voltage of 100V. 因為100伏特的反射電壓，比較800伏特解決方案它有更小的占空比。
- Shorter duty cycle for the same output power results in higher peak currents on the primary side. 小占空比實現同樣的功率輸出必須使用更高的一次側峰值電流。
- Phototube AD conversion, steering duty cycle, PWM-driven motor, the Hall element to modify the details of gun parts. 光電管AD轉換，舵機占空比，PWM驅動電機，霍爾元件測速 部分細節自行修改。
- Adjustable square wave generator, square wave to control the amplitude, frequency, duty cycle. 可調方波發生器，可以控制方波的幅值，頻率，占空比。
- Designed and manufactured to enterprise-class standards to provide enterprise reliability in high duty cycle environments. 設計和制造達到企業級標準,可在高強度運行環境下提供企業級穩定性。
- The LR series is completed by the hydraulic duty cycle crawler cranes range (HS series), which is similar to the LR series in design. LR系列還補充有結構類似于LR系列的液壓負載循環履帶式起重機系列(HS系列)。
- The calculated formula of duty cycle of printed circuit DC motor are analyzed in this paper. The results are verified for example. 摘要分析了印制繞組直流電機的斷續周期工作制下的計算公式，并通過實例加以驗證。
- By using a monostable multivibrator consist of 555 timers, a circuit of threshold processing PWM signal's duty cycle is proposed. 采用555定時器構成單穩態觸發器，設計出一套PWM波形占空比門限處理電路。
- This paper brings forward a method of threshold processing PWM signal s duty cycle by employing monostable multivibrator. 提出了采用單穩態觸發器對采集的PWM波形進行占空比門限處理的方法。
- The results show:the groove depth is more important for diffraction efficiency than the duty cycle,which is useful for fabrication of the BSG. 研究發現,在占寬比和槽深這兩個光柵結構參量中,槽深的變化對衍射效率更敏感。 這些都為取樣光柵的實際制作提供了有意義的結果。
- A clocking circuit programmed into a CPLD generates a synchronizing pulse for a slower instrument at half the duty cycle of a faster instrument. CPLD中可編程時鐘電路，為慢速儀器產生快速儀器等占空比的同步脈沖。
- Thanks to the low duty cycle, you can freely reduce the value of the optocoupler’s load resistor, R8, without sacrificing power efficiency. 由于低占空比，可以不損失功率而任意減少光耦負載電阻R8的值。
