您要查找的是不是：
- A good mechanics analysis approach was presented for reliability analysis and damage tolerance design of aerofoil ... 為機翼結構的可靠性分析和損傷容限設計提供了比較有價值的力學分析手段。
- DAMAGE TOLERANCE DESIGN FOR AIRCRAFT HUBS MADE OF CAST MAGNESIUM ALLOY 鑄鎂合金機輪損傷容限設計
- damage tolerance design 損傷容限設計
- Low-modulus skin is an effective design method for improving damage tolerance behavior of composite structures. 低模量蒙皮設計概念是改進復合材料結構損傷容限特性的一種有效的設計方法。
- In the end, a sample of spring absorber tolerance design is introduced. 最后給出了該方法在減震器彈簧公差設計中的應用實例。
- damage tolerant design 破損設計
- The method is easy to use in dimension and tolerance design and has a high accu racy. 在尺寸及公差設計中,該方法簡單、易行,而且可以獲得高的計算精度。
- The new engineering concept known as damage tolerance has been developed to provide quantitative guidance for this purpose. 一個新的工程概念即損傷容限正發展起來，為這個目的提供了定量的指導。
- What most people in North America call robust design refers to parameter design and tolerance design together. 在美國;參數設計及允差設計又被稱為穩健設計(Robust Design).
- During damage tolerance analysis, the probably crack types of key danger position are surface crack and edge angle crack in this article. 在損傷容限分析中，本文認為關鍵危險部位可能萌生的裂紋形態為表面裂紋與棱邊角裂紋；
- An impact damage tolerance reliability analysis method was discussed for composite structures by introducing an impact threat concept. 論述了基于沖擊威脅概念的復合材料結構沖擊損傷容限可靠性分析方法。
- As an important designing and indicating target of damage tolerance, the fatigue crack growth rate (FCGR) should be necessarily studied. 裂紋擴展速率作為損傷容限設計一個重要指標,以及表征材料損傷容限性能的重要方面,有必要對其開展較為深入的研究。
- The result shows that though such method we can efficiently obtain first tolerance design optimum for cam mechanism, and thus realizes First Product Correct (FPC). 結果表明該方法保證了凸輪機構公差設計一次達到最優，從而實現了一次產品成功。
- D braided compositese overcome the limitations of conventional laminated composites,such as low interlaminar strength and low damage tolerance. 編織結構復合材料克服了層合結構復合材料層間強度低，損傷容限低等缺點。
- In this article, models developing of computer-Aided Tolerance Design based VFP is discussed in detail, which aims at the key problem of tolerance design in mechanical design. 針對機械設計中的精度設計這一關鍵環節,研究了基于VFP的計算機輔助精度設計模塊開發詳細過程。
- Damage tolerance and durability meets the comprehensive requirements of prolongation of service life, high reliability and low maintenance cost of modern submarines. 摘要損傷容限與耐久性的結合體現了現代潛艇結構延長壽命、提高可靠性和降低維修成本的綜合要求。
- By contrastive analyses of some dimensional and tolerance design methods used in mechanical engineering design, a new dimension and tolerance design method by M onte Carlo method was developed. 通過對機械工程設計中所采用的幾種尺寸及公差設計方法的對比分析,提出了應用蒙特卡洛仿真法進行尺寸及公差設計的新方法。
- This paper discussed the des igning method of damage tolerance,studie d the life evaluation method of fatigue crack extension of long cracks and the d etermining method of dimension ao of ini tial crack. 論述了損傷容限設計方法 ,研究了長裂紋的疲勞裂紋擴展壽命估算方法和初始裂紋尺寸a0 的確定方法。
- Advanced aircraft power system and its control system was introduced and fault tolerant design of data bus was discussed. 摘要介紹了先進飛機供電系統及其控制系統的組成，并對數據通信總線的容錯設計進行論述。
- Damage tolerance：A post-replicative repair pathway in which the lesions are not repaired, but bypassed(tolerated) during replication. 損傷忍耐：是一種后復制修復途徑，在修復過程中其中損傷沒有被修復，而是被繞過（忍耐）過去。
