您要查找的是不是：
- Technical requirement on propulsion shafting align. 內河船舶推進軸系校中技術要求。
- Marine shafting is one of the main parts of ship power installation and alignment calculation is necessary for the safety and reliability of ship. 船舶推進軸系是船舶動力裝置的重要組成部分,校中計算是保證船舶推進軸系的安全、可靠工作不可缺少的環節。
- Has the shaft alignment been finished? 軸的對中任務完成了嗎?
- This paper presents the dynamic alignment calculation of Controllable-Pitch Propeller(CPP) propulsion shafting based on the improved three-moment equation. 采用基于改進的三彎矩方程進行調距槳推進軸系的動態校中計算。
- Then, `Retsina Shaft Alignment and vibration calculation software based on the Microsoft COM technology has been developed. 目前，國內關于船舶推進軸系校中和振動計算分析等理論研究和軟件開發，還停滯在引進國外技術和軟件的基礎上，開展對推進軸系校中及振動理論和計算軟件的研究與開發，具有較大的理論意義和重要的實用價值。
- In this paper, ship shafting alignment was analyzed in detail by use of three-moment method. 針對某一具體船舶軸系,利用三彎矩法對其校中作了詳細分析,給出軸系簡化處理方法和實際參數。
- Bushings (4): Furnishes shaft support at three locations for positive shaft alignment and actuator support. 襯套（4）：在三個位置上配置軸支撐，有利于軸校直和執行機構的支撐。
- Bushings: Furnishes shaft support at three locations for positive shaft alignment and actuator support. 襯套:在三個位置上配置軸支撐,有利于軸校直和執行機構的支撐。
- On alignment calculation of the submersible shafting 潛器軸系校中計算研究
- The article introduces the method of checking the bearing load by jack-up test after shafting alignment and illuminates the jack-up test with its application examples in a 1000 TEU container vessel. 介紹了在軸系按校中計算安裝后,通過頂升法檢測軸系中軸承所承受的負荷,來檢查軸系安裝是否正確。
- Different shafting alignment models are established in this paper through the detailed analysis of shafting alignments of VLCCs. 通過對巨型油輪傳動軸系的分析,建立了不同的軸系校中模型。
- crank shaft alignment measurement 曲軸對中測量
- method of testing shaft alignment 假軸找中法
- Test shows that proper shaft alignments,compensation capacity of the coupling and rotor dynamic balance etc.are essential to the noise control. 試驗表明,轉子間的對中狀況、聯軸器的補償能力以及軸系的動平衡等因素對機組噪聲有明顯的影響。
- Superficial Discussion on Shafting Alignment of Large - size Unit 淺談大型機組軸系找中心
- I did the calculation by the rule of three. 我是根據比例運算法則計算出來的。
- Could you align this table with those? 你能把這張桌子同那些桌子排成一行嗎？
- You are out in your calculation. 你失算了。
- Our company should align ourselves with theirs. 我們的公司必須與他們的公司合作。
